How to Set up a Tub Yourself
How to Set up a Tub Yourself
Blog Article
This article following next on the subject of How to Install a Bathtub is highly entertaining. You should look it over.
Mounting a bathtub isn't precisely brain surgery, but it does need strong plumbing, carpentry, as well as occasionally, tiling abilities. Changing an old bathtub with a brand-new one is also a reasonably challenging task. If the old tub is conveniently accessible, the job can move rapidly; if you need to open a wall surface to remove the old tub and also position the brand-new bath tub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly need a helper to vacate the old tub as well as embeded in the new one. Make certain you have actually qualified on your own for the work and fit trying it. Rather than employing a contractor to take over a halfway-completed job, it is far better to consider utilizing one prior to you begin. Possibilities are you might require a professional plumber to make tube connections.
This short article will certainly aid you install a new tub in your washroom if you have already gotten a brand-new bathtub and also don't need to alter the setup of your previous water supply pipes.
Your tools as well as product list should comprise the following:
Planning for the Installment
Firstly, the supporting frame supplied with the bath must be fitted (if needed) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is essential to ensure that if the tap comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps unit to prevent strain on the bath tub.
Fit the adaptable faucet ports to the bottom of the two faucets making use of 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you make use of every one of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be suited its final position.
Removing Old Taps
If you need to replace old faucets with new ones as a part of your installment, after that the first thing you should do is detach the water. After doing so, switch on the taps to drain pipes any type of water continuing to be in the system. The procedure of removing the existing faucets can be quite bothersome because of the limited gain access to that is often the instance.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a towel prepared for the continuing to be water that will originate from the pipes. As soon as the supply pipes have actually been removed, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from transforming throughout this process. When the faucets have actually been removed, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
Before moving on to fit the new taps, compare the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Mounting the Bathtub
Utilizing both wooden boards under its feet, put the bathtub in the needed position. The wood boards are valuable in evenly spreading out the weight of the bathtub over the location of the boards rather than concentrating all the weight onto four little points.
The following goal is to ensure that the tub is leveled all round. This can be achieved by examining the spirit level and readjusting the feet on the tub until the level reads degree.
To set up taps, fit the bottom of the furthest flexible faucet adapter to the ideal supply pipeline by making a compression join; then do the same for the other faucet.
Turn on the water system as well as inspect all joints as well as new pipework for leaks as well as tighten them if required. Fill up the tub and also check the overflow outlet and the normal electrical outlet for leakages.
Ultimately, take care of the bathroom paneling as described in the producer's instruction manual. Tiling and securing around the bathtub ought to wait up until the tub has been utilized a minimum of once as this will settle it into its final position.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic port to avoid damage to the thread. One end of the port fits on the plastic tail of the tap and the other end provides a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the mounting hole in the bath/basin guaranteeing that the washers are in place between the tap and the sink. Secure the tap in position with the manufacturer given backnut. When the faucet is securely in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with typical tap connectors. The former type should be attached to the faucet finishes initially, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bath meets the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move enough to fracture a rigid seal, causing the water to pass through the wall surface between the bath and the tiling, bring about issues with moisture and feasible leakages to the ceiling below.
You can choose from a selection of coloured sealers to blend in your fixtures and also fittings. They are sold in tubes and also cartridges, as well as are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of soaked paper or soft rope. Keep in mind to always load the tub with water prior to securing, to allow for the activity experienced when the bathtub is in usage. The sealant can fracture relatively early if you do not think about this motion prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily readily available on the market. It is advisable to fit the ceramic tiles using waterproof or waterproof glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I stumbled upon that page on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when browsing on the internet. Those who liked our article if you please remember to pass it around. Bless you for your time. Please visit our blog back soon.
Website
Report this page