Devices You Need to Install a New Bathtub
Devices You Need to Install a New Bathtub
Blog Article
Right here down the page you will find more sensible tips around How to Install a Bathtub.
Installing a bath tub isn't precisely rocket science, yet it does need solid plumbing, woodworking, and occasionally, tiling skills. Changing an old tub with a new one is additionally a moderately hard job. If the old bathtub is easily accessible, the task can move easily; if you have to open up a wall to get rid of the old tub and also position the brand-new tub, the job is much harder. In either instance, the job is within a home handyman's abilities, although you will require an assistant to leave the old bathtub as well as embeded in the new one. Make certain you have certified on your own for the task and also are comfortable trying it. Rather than employing a contractor to take over a halfway-completed task, it is better to think about using one before you start. Chances are you may require a specialist plumber to make tube links.
This short article will aid you mount a new tub in your washroom if you have currently acquired a new tub and also do not need to alter the setup of your previous water supply pipes.
Your devices and also material checklist must consist of the following:
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installment, then the first thing you ought to do is detach the water. After doing so, activate the taps to drain any type of water staying in the system. The procedure of getting rid of the existing faucets can be fairly problematic due to the restricted gain access to that is typically the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric prepared for the staying water that will certainly originate from the pipelines. When the supply pipelines have been removed, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from turning during this procedure. As soon as the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned of any old securing substance.
Before proceeding to fit the new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to prevent damages to the string. One end of the connector fits on the plastic tail of the tap and also the other end provides a link to the existing supply pipes.
If you need to fit a monobloc, after that you will require lowering couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, place the tap in the mounting opening in the bath/basin guaranteeing that the washing machines remain in place in between the tap and the sink. Safeguard the tap in position with the maker supplied backnut. When the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The previous type needs to be linked to the tap finishes first, tightening up only by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Mounting the Bathtub
Making use of the two wood boards under its feet, place the tub in the required setting. The wooden boards are practical in evenly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto 4 tiny points.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by examining the spirit level as well as adjusting the feet on the tub till the spirit level checks out degree.
To install faucets, fit all-time low of the furthest versatile faucet connector to the proper supply pipe by making a compression join; after that do the same for the other faucet.
Activate the supply of water and also check all joints as well as brand-new pipework for leakages and tighten them if needed. Load the bathtub and likewise examine the overflow electrical outlet and the normal outlet for leaks.
Lastly, take care of the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and sealing around the tub ought to wait up until the bathtub has been used a minimum of once as this will settle it into its final setting.
Getting ready for the Setup
To start with, the sustaining framework provided with the bath should be fitted (if required) according to the supplier's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps system to prevent strain on the bath tub.
Fit the adaptable tap connectors to the bottom of both faucets making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you utilize every one of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath need to currently be ready to be fitted in its last placement.
Tiling Around the Tub
In the area where the bathroom fulfills the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate sufficient to break a rigid seal, creating the water to pass through the wall between the bathroom as well as the tiling, resulting in difficulties with wetness as well as possible leakages to the ceiling below.
You can choose from a selection of coloured sealants to assimilate your components and installations. They are offered in tubes and cartridges, and also are capable of sealing voids up to a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill up the bathtub with water prior to sealing, to permit the motion experienced when the bathtub is in use. The sealer can crack relatively early if you do not think about this movement prior to sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily readily available on the market. It is a good idea to fit the tiles utilizing waterproof or water resistant glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
Do you appreciate reading up on How to Install a Bathtub? Try to leave a comment down below. We would be glad to listen to your ideas about this posting. We are looking forward to see you back again later on. Loved our blog entry? Please share it. Help another person discover it. Many thanks for your time. Visit us again soon.
Information Here
Report this page